B-Class car manuals
Nissan Micra: Forward-facing child restraint installation
using LATCH - Child restraints - Safety—Seats, seat belts and supplemental restraint system - Nissan Micra Owners Manual

Nissan Micra: Forward-facing child restraint installation using LATCH

Nissan Micra Owners Manual

For additional information, refer to all Warnings and Cautions in the “Child safety” and “Child restraints” sections of this manual before installing a child restraint.

Do not use the lower anchors if the combined weight of the child and the child restraint exceeds 65 lbs (29.5 kg). If the combined weight of the child and the child restraint is greater than 65 lbs (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.

Follow these steps to install a forward-facing child restraint using the LATCH system:

  1. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions.

Nissan Micra. Forward-facing webbing-mounted – step 2
Forward-facing webbing-mounted – step 2

  1. Secure the child restraint anchor attachments to the LATCH lower anchors. Check to make sure the LATCH attachment is properly attached to the lower anchors.

    If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point. For additional information, refer to “Installing top tether strap” in this section.

    Do not install child restraints that require the use of a top tether strap in seating positions that do not have a top tether anchor.

Nissan Micra. Forward-facing rigid-mounted – step 2
Forward-facing rigid-mounted – step 2

  1. The back of the child restraint should be secured against the vehicle seatback.

    If necessary, adjust or remove the head restraint/headrest to obtain the correct child restraint fit. If the head restraint/headrest is removed, store it in a secure place. Be sure to reinstall the head restraint/headrest when the child restraint is removed. For additional information about head restraint/headrest adjustment, refer to “Head restraints/headrests” in this section.

If the seating position does not have an adjustable head restraint/headrest and it is interfering with the proper child restraint fit, try another seating position or a different child restraint.

Nissan Micra. Forward-facing – step 4
Forward-facing – step 4

  1. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attachments.

    Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.

  2. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.

Nissan Micra. Forward-facing – step 6
Forward-facing – step 6

  1. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the LATCH attachment path. The child restraint should not move more than 25 mm (1 in), from side to side. Try to tug it forward and check to see if the LATCH attachment holds the restraint in place. If the restraint is not secure, tighten the LATCH attachment as necessary, or put the restraint in another seat and test it again. You may need to try a different child restraint. Not all child restraints fit in all types of vehicles.
  2. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 1 through 6.

Nissan Micra. Outboard seating positions
Outboard seating positions

  1. Top tether strap
  2. 2 Anchor point

Installing top tether strap

The child restraint top tether strap must be used when installing the child restraint with the LATCH lower anchor attachments.

First, secure the child restraint with the LATCH lower anchors (rear outboard positions only).

Rear bench seat

OUTBOARD SEATING POSITIONS

  1. Remove the head restraint/headrest and store it in a secure place. Be sure to reinstall the head restraint/headrest when the child restraint is removed. For additional information about head restraint/headrest adjustment, removal and installation, refer to Head restraints/headrests in this section.
  2. Position the top tether strap 1 over the seatback.
  3. Secure the tether strap to the tether anchor point 2 on the rear-parcel shelf behind the child restraint.
  4. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.
WARNING Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used to attach adult seat belts, or other items or equipment to the vehicle. Doing so could damage the child restraint anchorages.

The child restraint will not be properly installed using the damaged anchorage, and a child could be seriously injured or killed in a collision.

    Rear-facing child restraint installation using the seat belts

    Forward-facing child restraint installation using the seat belts

    Other info:

    Chevrolet Sonic. Starting the Engine
    The vehicle has a Computer-Controlled Cranking System. It assists in starting the engine and protects components. If the ignition key is turned to START and then released when the engine begins cr ...

    Chevrolet Sonic. Steps for Determining Correct Load Limit
    1. Locate the statement "The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs." on your vehicle’s placard. 2. Determine the combined weight of the driver and passenger ...

    Honda Fit. Specifications
    *1: Sport models *2: Not available on all models *1: Automatic transmission models *2: Manual transmission models *1: All models except Sport models *2: Sport models *3: U.S. models ...

    Manuals For Car Models


    © 2016-2024 Copyright www.b-auto.net 0.0098