Renault Clio manuals

Renault Clio: Trip settings

Renault Clio IV (2014-2019) Owners Manual / Getting to know your vehicle / Trip computer / Trip settings

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY








Examples of selections

Interpreting the display selected
a) Total mileage and trip mileage recorder.
b) Journey parameters.

Fuel used.

Fuel consumed since the last reset.
c) Average fuel consumption since the last reset.

The value is displayed after having travelled at least 400 metres since the last reset.

d) Current fuel consumption.

This value is displayed after a speed of approximately 20 mph (30 km/h) is reached.
e) Estimated range with remaining fuel.

The value is displayed after driving 400 metres.
f) Distance travelled since last reset.
g) Average speed since the last reset.

The value is displayed after driving 400 metres.



Examples of selections Interpreting the display selected
On-board computer with mileage-before-service message

h) Mileage before service or oil change.

Mileage before service With the ignition switched on, and the engine not running and the selected display is “Mileage before service”, press one of buttons 2 or 3 for about 5 seconds to display the mileage before service (distance or time to the next service). When the range approaches its limit, there are several possible scenarios:

  • distance/time remaining less than 900 miles (1,500 km) or one month: the message “Service due in” is displayed accompanied by the nearest term (distance or time);
  • distance equal to 0 miles or service date reached: the message “service vehicle” is displayed accompanied by the warning light.

The vehicle requires a service as soon as possible.
Resetting: To reset the distance before service, press and hold one of buttons 2 or 3 for approximately 10 seconds until the display shows the mileage permanently.

NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the event of an oil change, both the distance before the next service and the next oil change should be reset.
On-board computer with distance before next service message (cntd.) Interpreting the display selected

h) Mileage before service or oil change.

Mileage before service With the ignition switched on and the engine not running, and the selected display is “Mileage before service”, press one of buttons 2 or 3 for about 5 seconds to display the mileage before a service, then briefly press one of buttons 2 or 3 to view the range (distance or time remaining before the next service).

When the range approaches its limit, there are several possible scenarios:

  • distance/time remaining less than 900 miles (1,500 km) or one month: the message “Service due in” is displayed accompanied by the nearest term (distance or time);
  • range equal to 0 km/miles or service date reached: the message “service vehicle” is displayed accompanied by the warning light.

The vehicle requires an oil change as soon as possible.
Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed, door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can therefore decrease more quickly in some cases than the actual distance travelled.

Resetting: To reset the mileage before a service, press and hold one of buttons 2 or 3 for approximately 10 seconds until the display shows the range permanently.

NB: if a service is performed without changing the engine oil, only the mileage before the next service sho





Examples of selections

Interpreting the display selected
i) Reset the tyre pressure.

Please refer to the information on the “Tyre pressure loss warning” in Section 2.
j) Cruise control and speed limiter programmed speed.

Refer to the information in “Cruise control” and “Speed limiter” in Section 2.
k) Clock and temperature.

Please refer to the information under “Clock and exterior temperature”.

l) Trip log.

Successive display:

  • information messages (passenger airbag OFF etc.);
  • operating fault messages (check the injection system, etc.).

READ NEXT:

 Trip computer and warning system

Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages.

 Clock and exterior temperature

 Display A

To access display 1 for setting the time, press button 2 or 3. Wait for a few seconds. The hours and minutes flash and you are now in setting mode; press and hold button 2 or 3 to set the ho

SEE MORE:

 Sequential gearbox: Precautions for the repair

D4F or K9K, and JA3 or JA5 I - SEQUENTIAL GEARBOX WARNING If any operation is carried out on the electro-hydraulic unit, it is essential to clean the unit using a cleaning product and compressed air. Never leave the circuit open and never use a high pressure cleaner. II - SEQUENTIAL GEARBOX COMPUT

 Front end panel: General description

Note: The information contained in the following describes the general repair procedure for all vehicles having the same design for this part. Before reading the following general information, make sure that there are no special notes associated with the vehicle. These special notes are specified i

© 2016-2024 Copyright Renault Clio Owners Club