Automatic Transmission
position indicator light (A/T
models only)
When the ignition switch is in the ON position, this indicator light shows the shift lever position.
For additional information, refer to “Driving the vehicle” in the “Starting and driving” section of this manual.
Cruise main switch indicator
light (if so equipped)
The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational.
For additional information, refer to “Cruise control” in the “Starting and driving” section of this manual.
Engine start operation
indicator light (if so equipped)
For vehicles equipped with push button ignition this indicator illuminates when the ignition switch is in the LOCK, OFF, ACC or ON position with the shift lever in the P (Park) position.
Automatic transmission models:This indicator means that the engine will start by pushing the push-button ignition switch with the brake pedal depressed.
Manual transmission models:This indicator means that the engine will start by pushing the ignition switch with the clutch and the brake pedal depressed
Front fog light indicator
light (if
so equipped)
The front fog light indicator light illuminates when the front fog lights are ON. For additional information, refer to “Front fog lights” in this section.
Front passenger air bag status
light
The front passenger air bag status light will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.
For additional information, refer to “Front passenger air bag and status light” in the “Safety — Seats, seat belts and supplemental restraint system” section of this manual.
High beam indicator light
(blue)
This blue light comes on when the headlight high beams are on and goes out when the low beams are selected.
The high beam indicator light also comes on when the passing signal is activated.
Malfunction Indicator Light
(MIL)
If this indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction.
The may also come on steady if the
fuelfiller
cap is loose or missing, or if the vehicle runs
out of fuel. Check to make sure the fuel-filler cap
is installed and closed tightly, and that the vehicle
has at least 3 gal (11.4 L) of fuel in the fuel tank.
After a few driving trips, the light
should
turn off if no other potential emission control
system malfunction exists.
If this indicator light comes on steady for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/maintenance test. For additional information, refer to “Readiness for inspection/maintenance (I/M) test” in the “Technical and consumer information” section of this manual.
Operation
The MIL will come on in one of two ways:
The MIL may stop blinking and come on steady.
Have the vehicle inspected by a NISSAN dealer.
You do not need to have your vehicle towed to the dealer.
CAUTION Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system. |
Overdrive OFF indicator light
(A/T models only)
This light comes on when the overdrive function is OFF.
The automatic transmission overdrive function is controlled by the overdrive switch.
For additional information, refer to “Driving the vehicle” in the “Starting and driving” section of this manual.
Security indicator light
This light blinks whenever the ignition switch is placed in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational.
For additional information, refer to “Security systems” in this section.
Slip indicator light
This indicator will blink when the Vehicle Dynamic Control (VDC) system is operating, thus alerting that the vehicle is nearing its traction limits. The road surface may be slippery.
Turn signal/hazard indicator
lights
The appropriate light flashes when the turn signal switch is activated.
Both lights flash when the hazard switch is turned on.
Vehicle Dynamic Control
(VDC) OFF indicator light
This indicator light comes on when the VDC off switch is pushed to OFF. This indicates the VDC system is not operating.
Push the VDC off switch again or restart the engine and the system will operate normally. For additional information, refer to “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” section of this manual.
The VDC light also comes on when you place the
ignition switch in the ON position. The light will
turn off after about 2 seconds if the system is
operational. If the light stays on or comes on
along with the indicator light
while you are
driving, have the VDC system checked by a
NISSAN dealer.
While the VDC system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal.
Nissan Micra. Regulatory Information
FCC Regulatory information
CAUTION: To maintain compliance with
FCC’s RF exposure guidelines, use only the
supplied antenna. Unauthorized antenna,
modification, or attachments could damage ...
Chevrolet Sonic. Uniform Tire Quality Grading
Quality grades can be found where applicable on the tire sidewall between tread
shoulder and maximum section width. For example:
Treadwear 200 Traction AA Temperature A
The following information r ...
Mazda 2. High Beam Control System (HBC)
The High Beam Control System (HBC) determines the conditions in front of the
vehicle
using the Forward Sensing Camera (FSC) while driving in darkness to
automatically switch
the headlights betwe ...